Shenzhen Link-Card Tech Co., LTDMenu

Industrial Infrared Thermal Imager: HDMI/AHD/TVI/SDI Multiple Output Formats

Industrial Infrared Thermal Imager: HDMI/AHD/TVI/SDI Multiple Output Formats

    A1T Industrial Infrared Thermal Imager

    1. Overview

    The A1T series industrial infrared thermal imagers are built on Link-Card Tech uncooled vanadium oxide infrared detectors, targeting industrial monitoring, equipment inspection and security integration applications. The product family offers four video output formats — HDMI, AHD, SDI and TVI — covering direct-connect displays, coaxial surveillance systems, broadcast-grade transmission and industrial HMI panels. All models additionally support driver-free USB UVC output (in YUV, MJPG or RAW14bits format), allowing professional PC software to capture raw infrared data directly.

    The 640×512 resolution is the mainstream recommended configuration for the A1T module, with 1.5W power consumption; 384×288 is available as a standard economy option at 1.2W; and a 1280×1024 high-definition configuration is offered as an upgrade, providing four times the pixel coverage of 640×512 for large-area precision temperature measurement. The module (excluding lens) measures only 32×32×43.70mm and weighs 59g, powered from USB Type-C 5V DC. Its M25×0.5 threaded mount accepts germanium glass infrared lenses of various focal lengths, and the module can be embedded into a wide range of industrial equipment housings to deliver customised thermal imaging capability.

    2. Technical Specifications

    The table below lists the complete technical specifications for both A1T resolution configurations, with 640×512 as the mainstream recommendation and the 1280×1024 high-definition configuration available on request. On NETD, the 640×512 configuration achieves ≤35mK and the 384×288 configuration ≤40mK, giving the 640×512 version a clear advantage in thermal sensitivity.

    Parameter 384×288 Configuration 640×512 Configuration
    Detector Type Uncooled vanadium oxide infrared detector Same as left
    Resolution 384×288 640×512
    Pixel Pitch 12μm 12μm
    Spectral Response 8-14μm 8-14μm
    Frame Rate 25/30/50Hz 25/30Hz
    NETD ≤40mK@25℃,F#1.0 ≤35mK@25℃,F#1.0
    Processor ARM+DSP ARM+DSP
    Memory 2Gb DDR 2Gb DDR
    Shutter Correction Automatic / manual Automatic / manual
    Digital Zoom 1.0-4.0× 1.0-4.0×
    Electronic Compass Supported Supported
    Motion Sensor Supported Supported
    Reticle Show / hide / move Same as left
    Power Consumption 1.2W 1.5W
    Power Supply USB Type-C 5V DC USB Type-C 5V DC
    Dimensions (excl. module) 32×32×43.70mm Same as left
    Weight (excl. module) 59g 59g
    Lens Mount M25×0.5 M25×0.5
    Operating Temperature -20℃~60℃ -20℃~60℃

    3. System Architecture

    The A1T system consists of the infrared optical assembly, the uncooled vanadium oxide detector, the ARM+DSP signal processing platform and the multi-format video output interfaces.

    LWIR imaging physics: every object above absolute zero emits infrared radiation. By the Stefan-Boltzmann law, blackbody radiant power density is proportional to the fourth power of temperature (P = εσT⁴, where ε is emissivity and σ is the Stefan-Boltzmann constant, 5.67×10⁻⁸ W·m⁻²·K⁻⁴). The 8-14μm band lies within the long-wave infrared atmospheric window with atmospheric transmittance >80% (1km horizontal path), making it the band of choice for thermal imaging of ground targets. After a detector pixel absorbs target radiation its temperature rises and the resistance of the vanadium oxide (VOx) film changes accordingly (TCR of approximately -2%~-3%/K); the ROIC readout circuit converts this resistance change into an electrical signal. Detector responsivity depends on pixel thermal conductance, heat capacity and TCR; typical NETD for uncooled detectors is 30-50mK.

    Signal processing platform: an ARM+DSP dual-core architecture. The ARM core runs control logic (communication, UI, sensor management) while the DSP core executes the real-time image processing pipeline. 2Gb of DDR memory buffers multiple frames for temporal noise reduction. The video output section integrates a different encoder depending on model: HDMI models contain an HDMI transmitter outputting 1024×768@50Hz digital video; AHD/TVI models use a coaxial encoder outputting 720P/PAL analogue video, compatible with existing coaxial surveillance cabling; SDI models use a serial digital interface encoder for broadcast-grade lossless video. The USB UVC interface outputs YUV (compressed preview), MJPG (motion JPEG) or RAW14bits (raw 14bit data) in parallel.

    Image processing algorithms: the A1T embeds a complete infrared image processing pipeline; the function of each algorithm is listed in the table below.

    Algorithm Function
    NUC Non-uniformity correction, eliminating detector pixel response variation
    AGC Automatic gain control, dynamic range compression
    2D/3D Noise Reduction Joint spatial-temporal noise reduction
    Pseudo-Colour Mapping Multiple palettes (white-hot / black-hot / red-hot / blue-green flame / iron red / spectrum)
    DDE Digital detail enhancement
    Bad Pixel Compensation Replaces defective pixels to preserve image integrity
    Shutter Correction Automatic / manual mechanical shutter reference correction

    4. Interface Definition

    The defining feature of the A1T series is the range of video output formats available; users select the model matching their integration scenario. Every model also provides USB UVC output for direct capture by PC software.

    Model Video Output Physical Interface Output Resolution
    A1T-HDMI HDMI + USB(UVC) Type-C HDMI: 1024×768@50Hz; USB: 384×288/640×512
    A1T-AHD AHD + USB(UVC) MCX + Type-C AHD: 720P/PAL; USB: 384×288/640×512
    A1T-SDI SDI + USB(UVC) MCX + Type-C SDI: 720P/PAL; USB: 384×288/640×512
    A1T-TV TVI + USB(UVC) MCX + Type-C TVI: 720P/PAL; USB: 384×288/640×512

    USB UVC output formats: the YUV format outputs an AGC-processed 8bit video stream at the detector frame rate, suited to real-time preview. The MJPG format outputs JPEG-compressed frames with low bandwidth requirements, suited to network transmission and storage. The RAW14bits format outputs unprocessed raw 14bit detector data containing the full radiometric information, from which professional software can perform quantitative temperature analysis and custom image processing. The three formats are selectable through the USB descriptor.

    5. Application Scenarios

    Mine and tunnel high-temperature risk monitoring: in underground roadways and tunnel construction environments, abnormal surrounding-rock temperature can indicate heat hazard or a latent fire risk. The A1T connects directly to an explosion-proof underground display over HDMI, showing the surrounding-rock temperature distribution in real time. Thermal sensitivity of NETD≤40mK resolves temperature differences of 0.04℃, sufficient to distinguish abnormal thermal gradient regions in the rock. SDI models transmit losslessly over long distances to a surface control centre, reaching over 100m on coaxial cable, or further via fibre conversion.

    Electrical equipment condition monitoring: high-voltage switchgear, transformers, busbar joints and similar electrical equipment develop local temperature rise when contacts degrade, loads are exceeded or insulation ages. The A1T thermal imager measures equipment surface temperature fields without contact, allowing faults to be predicted from temperature-rise trend analysis. The 640×512 model provides greater pixel coverage, capturing an entire switchgear panel in a single frame. AHD/TVI models integrate into existing coaxial surveillance systems with no re-cabling required.

    Pipeline and storage tank inspection: damaged steam pipeline insulation, heating pipeline leaks and tank level detection can all be identified through infrared thermal imaging. Surface temperature at a break in pipeline insulation is markedly higher than along healthy sections, appearing as a bright region in the thermal image. The liquid level line inside a tank is discernible in thermal imagery because of the heat capacity difference between the liquid and gas phases.

    Industrial HMI integration: the A1T-HDMI model connects directly to an industrial touch screen or HMI panel over its Type-C interface, embedding the thermal image into a production line monitoring interface. Digital zoom (1.0-4.0×) lets operators magnify a region of interest without changing lenses, and the reticle function supports precise positioning of measurement points.

    6. Mechanical Dimensions

    The A1T module measures 32×32×43.70mm (excluding lens) and weighs 59g. The M25×0.5 lens mount accepts the full range of Link-Card Tech infrared lenses (9.1mm/13mm/19mm/25mm/35mm/50mm and other focal lengths). The MCX connector (on AHD/SDI/TVI models) is a miniature coaxial connector with a small footprint. The Type-C interface carries both power and USB data. M2.5 mounting holes are provided at the four corners of the PCB for mechanical fixing.

    Dimension Parameter Value Notes
    Dimensions (excl. module) 32×32×43.70mm Including lens mount
    Weight (excl. module) 59g Including PCB and connectors
    Lens Mount M25×0.5 Threaded connection
    Mounting Holes 4×M2.5 Four-corner fixing
    Power Supply 5V DC / Type-C USB powered

    The A1T series accepts infrared lenses of various focal lengths, allowing users to select flexibly according to inspection distance and required field of view. The standard lens is 25mm; the 9.1mm short focal length suits close-range wide-angle monitoring and the 50mm telephoto suits long-range precision temperature measurement.

    Lens Focal Length Field of View (FOV) Application
    9.1mm Wide FOV Close-range wide-angle monitoring / large-area coverage
    25mm Medium FOV Standard industrial monitoring (standard fit)
    35mm Medium-narrow FOV Medium to long range inspection
    50mm Narrow FOV Long-range precision temperature measurement

    7. Ordering Information

    The A1T series is offered as six standard models combining output format and resolution. When selecting, first determine the video connection method required by the integration scenario (direct HDMI / coaxial AHD / SDI), then choose the resolution — the 640×512 mainstream model is recommended first, the 384×288 standard economy version suits budget-constrained scenarios, and the 1280×1024 high-definition model is available on request.

    Model Output Format Interface Application
    A1T-HDMI-640 HDMI+USB Type-C Mainstream recommendation: HD industrial inspection
    A1T-AHD-640 AHD+USB MCX+Type-C Mainstream recommendation: HD surveillance integration
    A1T-SDI-640 SDI+USB MCX+Type-C Mainstream recommendation: HD long-distance transmission
    A1T-HDMI-384 HDMI+USB Type-C Standard economy version: direct display / HMI
    A1T-AHD-384 AHD+USB MCX+Type-C Standard economy version: coaxial surveillance integration
    A1T-SDI-384 SDI+USB MCX+Type-C Standard economy version: broadcast-grade long distance

    8. References

    1. LWIR radiation and the Stefan-Boltzmann law: Incropera F.P. et al., "Fundamentals of Heat and Mass Transfer", 7th Edition, Wiley, 2011.

    2. Uncooled vanadium oxide microbolometer principles and NETD derivation: Rogalski A., "Infrared Detectors", 2nd Edition, CRC Press, 2011.

    3. SDI/AHD/TVI/HD-CVI coaxial high-definition video transmission standard technical white papers.

    4. Infrared inspection and diagnosis standard for electrical equipment: DL/T 664-2016, "Application rules of infrared diagnosis for live electrical equipment".

    5. USB Video Class (UVC) specification: USB-IF, "USB Device Class Definition for Video Devices", Revision 1.5.

    【Back】

Need selection advice or a custom solution?

Link-Card provides thermal module selection, secondary development and full-system solution support.

Our sales team will reply to the email or phone number you leave. You can also email sales@link-card.com directly.