The infrared lens is the first optical element in the thermal imaging chain—its material, focal length, aperture, and coatings directly determine the system's spatial resolution and radiometric capability. This article explains the infrared optical material system, the key optical parameters, athermalization design, and LWIR/MWIR/SWIR band matching, and surveys major Chinese suppliers of infrared lenses and optical materials, together with the germanium-free shift toward chalcogenide precision molding.
1. Why an infrared lens differs from a visible-light lens
An infrared lens is an optical assembly that focuses radiation in the 1–14 μm band onto a focal plane array (FPA). It differs from a visible-light lens in three fundamental ways.
Material. Ordinary borosilicate and crown glasses absorb strongly beyond about 2.5 μm; mid- and long-wave lenses use germanium, silicon, chalcogenide glass, zinc sulfide, or zinc selenide. Where the energy comes from. Thermal imaging collects radiation emitted by the scene. Irradiance on the FPA scales with transmission and with 1/(F#)². Entrance-pupil diameter is fixed only after focal length and field of view are chosen; aperture alone is not “the” sensitivity knob. Diffraction. Wavelengths are 2–20× those of visible light, and the Airy disk scales by the same factor. A surface-figure tolerance quoted in waves (λ/10, for example) is looser in micrometres than the visible-light equivalent. What is tight at f/1 in the LWIR is the aspheric departure, the alignment sensitivity, and the fact that the Nyquist frequency of a 12 μm pixel already sits on the falling diffraction MTF, so figure and air-space errors spend the remaining MTF directly.
2. The infrared optical material system
Material selection is the most consequential decision in infrared lens design. Each material is transparent only over a specific band, and the designer must balance transmission range, refractive index, thermo-optic coefficient, manufacturability, density, and cost. Figure 1 maps the transmission bands of common infrared materials against the three atmospheric windows; Table 1 lists their key parameters.
Germanium (Ge) is the mainstream material for 8–14 μm LWIR lenses. Its refractive index is about 4.0 at 10 μm, and this high index enables compact single- or double-element designs. Its weaknesses are a large thermo-optic coefficient (dn/dT ≈ +396×10⁻⁶/K)—the refractive index changes sharply with temperature, which is the root driver of athermalization—and the fact that germanium is opaque below about 2 μm and dense at 5.32 g/cm³, making it relatively heavy and costly.
Silicon (Si) transmits well from 1.2 to 7 μm, with a refractive index of about 3.42 at 4 μm. It is cheaper than germanium, harder, and machines well by diamond turning, and is often used as a wide-field correcting element in multi-element MWIR systems. Chalcogenide glass—an amorphous material formed from chalcogen elements (S, Se, Te) combined with As, Ge, Ga, and others—transmits roughly 1–12 μm with a refractive index of 2.4–2.8, slightly lower than germanium. Its key advantage is that it can be precision-molded, which suits high-volume, low-cost production; its dn/dT is also lower than germanium's, so its share in cost-sensitive LWIR designs keeps rising.
Zinc sulfide (ZnS, 0.4–14 μm) and zinc selenide (ZnSe, 0.6–18 μm) cover wide bands; ZnSe offers one of the broadest spectral coverages among common infrared materials, but its lower refractive index (about 2.4 at 10 μm) and weaker resistance to mechanical surface damage limit it in high-volume OEM assemblies, while ZnS is often paired with germanium for optical athermalization. Gallium arsenide (GaAs, 0.9–17 μm) is used for wide-band and high-power applications. Short-wave infrared (SWIR) relies mainly on sapphire (0.15–5.5 μm) and fused silica (0.2–3.5 μm).
| Material | Transmission | Refractive index (typ.) | dn/dT | Processing | Density | Typical use |
|---|---|---|---|---|---|---|
| Germanium (Ge) | 2–14 μm | ~4.0 @10μm | High (≈ +396×10⁻⁶/K) | Diamond turning, grinding/polishing | 5.32 g/cm³ | LWIR mainstream, compact designs |
| Silicon (Si) | 1.2–7 μm | ~3.42 @4μm | Moderate | Diamond turning | 2.33 g/cm³ | MWIR correcting element |
| Chalcogenide glass | ~1–12 μm | 2.4–2.8 | Low | Precision molding (high volume) | ~4.4 g/cm³ | Cost-sensitive / high-volume LWIR |
| Zinc sulfide (ZnS) | 0.4–14 μm | ~2.2 @10μm | Low | CVD, grinding | ~4.1 g/cm³ | Wide-band windows; athermalization with Ge |
| Zinc selenide (ZnSe) | 0.6–18 μm | ~2.4 @10μm | Moderate | CVD, grinding | ~5.3 g/cm³ | Broad-band high transmission; CO₂ laser |
| Gallium arsenide (GaAs) | 0.9–17 μm | ~3.3 | Moderate | Crystal machining | ~5.3 g/cm³ | Wide band, high power |
| Sapphire | 0.15–5.5 μm | ~1.75 @1.5μm | Low | Crystal machining, polishing | ~4.0 g/cm³ | SWIR windows, high hardness |
| Fused silica | 0.2–3.5 μm | ~1.45 | Very low | Grinding/polishing | ~2.2 g/cm³ | SWIR / near-infrared |
3. Key optical parameters: focal length, F-number, FOV, and MTF
An infrared lens is specified mainly by its effective focal length (EFL), F-number, and field of view (FOV). The F-number is defined as F/# = EFL / D, where D is the entrance-pupil diameter. A smaller F-number means a larger aperture, more radiant flux per pixel, higher SNR, and lower NETD. Uncooled microbolometers typically need f/1.0–f/1.2 lenses to compensate for their relatively high noise floor, whereas cooled photon detectors—whose noise-equivalent power is orders of magnitude lower—can tolerate larger F-numbers of f/2.0–f/4.0.
Horizontal field of view is set by the pixel pitch p, the array format N, and the focal length: FOV_H = 2 · arctan( N · p / (2 · EFL) ). For a 12 μm pitch, 640×512 array, a 19 mm lens gives a horizontal FOV of about 23°; doubling the focal length to 38 mm narrows it to about 11.5°. The sound selection order is to fix the FOV from the application first, then the focal length—because the focal length in turn determines the mechanical interface to the module and the entrance-pupil diameter needed to hit the sensitivity target.
Image quality is the modulation transfer function (MTF). The upper spatial frequency is the FPA Nyquist frequency 1/(2p). At 12 μm, a system MTF of 0.3–0.4 at Nyquist covers most surveillance and inspection work. The pure diffraction limit at f/1.0 is about 0.49 for λ = 10 μm and a circular pupil, so design and alignment do not have a wide margin. Measurement can follow ISO 15529. Distortion under 2% is usually left uncorrected in surveillance imagery; a diagonal field beyond 60° can reach 5–10% and needs a geometric correction. Axial and lateral color still exist. The atmospheric window is wide relative to material dispersion, so two or three materials with air-spaced elements are the usual correction. Cemented doublets are uncommon: the cement’s transmission and thermal stress are poor across a wide temperature range at 8–14 μm.
4. Athermalization: holding focus across a wide temperature range
An infrared lens deployed outdoors must hold focus over a wide temperature range: defense-grade systems typically require −40 °C to +71 °C, and commercial OEM products −20 °C to +60 °C. The refractive index of every optical material and the physical dimensions of the barrel change with temperature; for a germanium-based LWIR lens, a ±20 °C shift can move the back focus beyond the FPA's depth of focus, so athermalization is almost always required for field systems. There are three technical routes.
- Passive optical athermalization: materials with different thermo-optic coefficients are combined within one lens group so their focal shifts cancel—typically a ZnS element compensating a Ge element. It is passive with no moving parts, but places high demands on design and material pairing.
- Passive mechanical athermalization: barrel materials with different coefficients of thermal expansion—aluminum, Invar, or carbon-fiber composite—shift the detector or a lens group along the axis as temperature changes. There is no motor, but there is relative motion, and clearance and friction enter the error budget. Compact fixed-focus modules for vehicles, robots, and industrial inspection mostly use this route.
- Active athermalization: an electrically driven focus mechanism, commanded by a temperature sensor or a contrast-maximization algorithm. It adds weight, firmware complexity, and potential failure points, and is usually reserved for long-focal-length surveillance systems where thermal defocus exceeds what passive methods can correct.
5. Band matching: LWIR / MWIR / SWIR
The spectral band of the FPA determines the compatible lens materials, anti-reflection coatings, and performance envelope; the three bands are not interchangeable—a lens designed for one performs poorly, or not at all, in another. LWIR (8–14 μm) uses germanium or chalcogenide lenses with AR coatings optimized for the 8–12 μm window. MWIR (3–5 μm) typically uses silicon or germanium lenses with a sapphire dewar window; cooled systems are especially sensitive to background radiation introduced by poor lens matching, so cold-shield efficiency (the ratio of the exit pupil imaged onto the cold stop) must be verified to avoid background-limited performance degradation. SWIR (0.9–1.7 μm) uses near-infrared-optimized fused silica or sapphire lenses whose materials and coatings differ entirely from LWIR and MWIR.
On airborne and drone platforms, payload volume and weight are tightly constrained, so material density becomes a secondary but non-negligible factor: germanium's density of 5.32 g/cm³ is markedly higher than chalcogenide glass's ~4.4 g/cm³, a difference that becomes significant in large-aperture applications and one reason chalcogenide is valued for lightweight payloads.
6. The Chinese infrared lens and material supply landscape
A fairly complete domestic chain has formed in China, spanning infrared optical materials, lens-element machining, and lens assembly, and it is showcased at platforms such as the China International Optoelectronic Exposition (CIOE). The 27th CIOE will be held September 9–11, 2026 at the Shenzhen World Exhibition & Convention Center; its Infrared Technology & Application Show is one of the more influential infrared exhibitions in the Asia-Pacific region, with a defined scope covering infrared optical materials (germanium, silicon, ZnSe, GaAs crystals, chalcogenide glass, and filters) and infrared modules (infrared lenses, manual and motorized lenses). It is a useful window onto the domestic infrared lens and material supply chain. The official notable-exhibitor lists include Guangzhi Technology, Zhaosheng Technology, CNGE, Kunming Quanbo Infrared, and Guojinghui in the Infrared Technology & Application Show, and Phoenix Optical, Sunny Optical, and FORECAM in the Precision Optics & Camera Technology Show; together with the official exhibitor search system, these lists map out the main landscape of lens suppliers. Table 2 summarizes representative players across the chain, compiled from public sources, with each supplier name linking to its official website.
| Supplier | Role in the chain | Materials / products | Band / notes |
|---|---|---|---|
| Yunnan Germanium | Upstream materials: germanium mining—deep processing | Infrared-grade Ge single crystals and blanks, Ge elements / lenses, optical systems | One of the most vertically integrated germanium chains in China; Ge optics |
| CNGE / Zhongzhe Technology | Infrared optical and semiconductor materials and components | Infrared optical materials and related components based on germanium crystals | Nanjing; CIOE 2026 Infrared Show exhibitor |
| Guojinghui (GRINM Group) | Infrared optical materials + elements / lenses | CVD ZnS, CVD ZnSe, Ge/Si crystals, chalcogenide glass; custom precision elements and infrared imaging lenses | Materials through lenses; security / automotive / thermal imaging; link points to parent GRINM Advanced Materials |
| Ningbo Sunny Infrared Optics | One-stop elements + lenses (Sunny Optical subsidiary, 2006) | Security / thermometry / automotive / outdoor thermal lenses; athermalized, manual, motorized, dual-FOV, high-ratio zoom | Mainly LWIR; zoom up to 30×; e.g., 13 mm/1.0, 25–100 mm f/1.0 |
| Guangzhi Technology | Materials to systems, full chain | Ge, ZnSe, ZnS, chalcogenide glass; 600+ lens types (fixed focal / athermal / manual & motorized focus / IR microscopy) plus detectors and thermal imagers | Two main businesses: infrared optics and high-performance aluminum alloys |
| FORECAM / Fuguang | Full-spectrum lenses + optoelectronic systems | UV / visible / NIR / mid- and long-wave IR; custom (special/aerospace) + non-custom (automotive/security) | SW/MW/LW IR detection lens series; aspherical + IR correction |
| Phoenix Optical | Optical lenses and optoelectronic modules | Infrared lenses (including motorized focus), machine-vision, ITS, automotive lenses | Established state-owned optics platform; CIOE Precision Optics Show exhibitor |
| Foshan Hwaguo Optical | Full-band lens customization | LWIR thermal-imaging lenses, sight objective / eyepiece lenses, low-light lenses, industrial / medical / UV lenses | Founded in Foshan in 1992 by Taiwan-listed Kinko Optical; moving into dedicated thermal-imaging lenses |
| Wavelength Opto-Electronic | Laser optics + infrared optical elements / lenses | Chalcogenide precision molding; germanium-free infrared optics | MWIR / LWIR; chalcogenide substituting germanium to cut cost |
| Hongjing Optoelectronic | Optical lenses and optoelectronic modules | Infrared lenses and modules (main business in automotive / ITS precision optics) | An infrared-lens R&D and industrialization program is under way |
| Kunming Quanbo Infrared | Windows / lenses: design–machining–assembly–test | Chalcogenide vacuum melting (99.9999% feedstock) + spherical/aspherical precision molding + coating and assembly | Molded chalcogenide infrared lenses; CIOE 2026 Infrared Show, Hall 8, booth 8C71 |
| Zhaosheng Technology | Cores + lenses + complete systems | Thermal-imaging cores, assemblies, lenses, elements (among the first domestic volume producers of shutterless cores) | End-to-end infrared solutions |
| Mavin Optics (Zhongshan Meijing) | Near-IR / low-light lenses and filters | Night-vision lenses (near-IR focal-shift compensation), dual-channel IR-cut filters | Focused on near-infrared and security; not an LWIR thermal lens supplier |
Note that Table 2 lists representative suppliers compiled from public sources; it is neither an exhaustive directory nor a ranking, and the material and lens stages often overlap (for example, Yunnan Germanium extends from germanium materials into lenses, Guangzhi Technology from materials into detectors and thermal imagers, and Guojinghui from materials into imaging lenses). One company has no standalone website, and its link points to the parent company's site. Business scope follows each supplier's website and periodic reports; for selection, always rely on datasheet values measured under stated test conditions.
7. Material trend: germanium price volatility and germanium-free chalcogenide molding
Germanium has long been the default LWIR lens material. Export and supply tightened in 2023, and prices stayed high after 2024, which is when civilian programs started treating alternatives as a real option. Chalcogenide glass can be precision-molded, its dn/dT is lower than germanium’s, and molding avoids most of the material loss of grinding and polishing. The index is only 2.4–2.8. Uncooled cameras have no cold shield. A material swap is compared at the same F-number on element count, transmission, stray light, and MTF, not on cold-shield efficiency, which belongs to cooled systems. The lower index usually means more elements for the same power, and coating loss and alignment error rise with them. The cost crossover depends on annual volume and the MTF specification.
In terms of industry structure, France's Umicore was an early player to master both chalcogenide glass production and precision molding; domestically, Ningbo Sunny Infrared, Kunming Quanbo Infrared, and Wavelength Opto-Electronic have also established chalcogenide precision-molding capability, and domestic molded chalcogenide infrared lenses are scaling up. For system and module makers, the material choice has moved beyond a pure optical-performance comparison to a combined weighing of performance, cost, weight, and supply stability.
Conclusion
The infrared lens is the first optical gate of a thermal imaging system: the material determines spectral transmission, weight, and cost; focal length and F-number determine field of view and sensitivity; athermalization determines usability across temperature; and coatings determine transmission efficiency and stray-light suppression. All four must be evaluated together against the FPA specification, mechanical envelope, and environmental constraints rather than traded off in isolation. Understanding the infrared optical material system and the capability envelope of the domestic supply chain is the prerequisite for a sound selection among cost, performance, and lead time.
